Skip to content
GNPC-1 Technical Datasheet & Specifications

Technical datasheet - Google Nest Cam power adapter

GNPC-1 Technical Datasheet

Electrical ratings, run budget, dimensions, protection and the ETL listing of the GNPC-1 Google Nest Cam power adapter.

Document DS_GNCP-1_05-2026, the datasheet revision this page follows. Applies to GNPC-1, all production units, and every figure matches the product page.

First page of the GNPC-1 Technical Datasheet PDFTechnical Datasheet
PDF - DS_GNCP-1_05-2026
Output7.5V DC, 1.5Athe rating for the GPJ15 Nest Cam Outdoor (wired, 2nd gen)
Input100-240V ACfrom any US outlet, 50/60 Hz, 0.5A, two-prong plug
Run budgetUp to 75 ft22.9 m on 18 AWG or heavier conductor
Terminals+ and - screwsno captive cord; the Google-supplied cable lands here
MountingSecurity screw tabanchors flat to the wall plate
ListingsETL - UL 1310Intertek 5030071 80CD, CSA C22.2 No. 223, Level VI

01Overview

What this datasheet covers

The GNPC-1 is a Class 2 power adapter for wired Google Nest Cam installs. It plugs into an indoor outlet, takes 100-240V AC, and puts out 7.5V DC at 1.5A. That's the adapter rating Google lists for the GPJ15 variant of the Nest Cam Outdoor (wired, 2nd gen). It's ETL Listed by Intertek, and this page carries every figure from the printed datasheet so you can quote it on a job.

Transformer-only is the point, and we built it that way on purpose. There's no captive cord. The adapter ends in two screw terminals marked + and -, and the camera cable Google supplies to security professionals lands right there. So you carry one power SKU, and you plan one run of up to 75 ft (22.9 m) on 18 AWG or heavier conductor.

Below you'll find the features, the full specification tables, which camera variant the rating serves, the mechanical details, a three-step install and the ordering notes. The datasheet PDF is the same document in print form, and the installer guide walks through the cable routes in more detail.

Before you start

Indoor use only, and the adapter's own label says why: Risk of electric shock. Dry locations use only. So keep the GNPC-1 at an interior outlet and run the cable out to the camera.

Worth knowing

The 75 ft figure is a run budget at 18 AWG, not a target. Heavier wire buys you margin, and thinner wire spends the budget faster than the length alone suggests.

02Features

What the GNPC-1 gives you

  • The 7.5V DC, 1.5A rating that Google publishes for the GPJ15 variant of the Nest Cam Outdoor (wired, 2nd gen), from a 100-240V AC input.
  • Transformer-only, so it pairs with the camera cable Google supplies to security professionals, and there's no second cable to pay for.
  • Two screw terminals marked + and - in place of a captive cord, which is where that cable lands.
  • A published run budget of up to 75 ft (22.9 m) on 18 AWG or heavier conductor, so you can plan the route on paper.
  • A security mounting screw hole, which anchors the adapter flat to the wall plate so it can't be pulled out of the socket.
  • Short-circuit protection that shuts the output down on a fault and recovers on its own once the fault clears.
  • NTC thermal protection, which covers inrush current and overheating.
  • ETL Listed by Intertek under control number 5030071 80CD, to UL 1310 and CSA C22.2 No. 223, and it's an Efficiency Level VI supply.

Short-Circuit Protection: The power adapter includes automatic short-circuit protection. If a short circuit occurs at the output terminals, the adapter safely shuts down and automatically recovers once the fault is removed.

Temperature Protection: Temperature protection is provided through NTC (Negative Temperature Coefficient) components to help reduce inrush current and prevent overheating.

Wiring: Supports 18 AWG wire with cable runs up to 75 ft (22.9 m).

03Specifications

GNPC-1 specifications

Every figure here matches the GNPC-1 product page and the adapter's own label, so you can quote any of the three.

Electrical
Model GNPC-1
Input 100 - 240V 50/60Hz, 0.5A
Output 7.5V, 1.5A DC
Class Class 2 Power Unit; Class II (double insulated)
Efficiency Efficiency Level VI external power supply
Output wiring and compatibility
Termination Two screw terminals marked + and -; no captive cord
Maximum run 75 ft (22.9 m)
Minimum wire gauge 18 AWG or heavier
Application Power adapter for wired Google Nest Cam installs
Rating matched 7.5V DC / 1.5A - the adapter rating Google's Safety and Regulatory Guide lists for the GPJ15 variant of the Nest Cam Outdoor (wired, 2nd gen)
Camera cable Pairs with the camera cable Google supplies to security professionals
Physical and protection
Dimensions 1.71 x 1.15 x 3.75 in.
Plug type Two-prong plug-in (NEMA 1-15P)
Mounting Integrated security mounting screw hole, so the adapter anchors to the wall plate
Short circuit Automatic shutdown on an output fault; self-recovers once the fault clears
Thermal NTC inrush limiting and overheat protection
Use Indoor use only; dry locations only; residential and commercial
Certifications and compliance
Safety listing ETL Listed by Intertek, control number 5030071 80CD
Standards Conforms to UL STD. 1310; certified to CSA STD. C22.2 No. 223
Origin Made in Vietnam
Document DS_GNCP-1_05-2026, GNPC-1 Technical Data Sheet

Use Class 2 rated conductor, 18 AWG or heavier, and keep the total run within the 75 ft rating. Match polarity at the + and - terminals and tighten the conductors fully under the screw heads. Mount the adapter and dress the run per Google's install guide for your camera model.

04Compatibility

Cameras and cables the GNPC-1 works with

We built the GNPC-1 as a 7.5V DC, 1.5A Class 2 power adapter for wired Google Nest Cam installs. Google's Safety and Regulatory Guide lists the adapter rating each variant of the Nest Cam Outdoor (wired, 2nd gen) takes. The GPJ15 variant takes 7.5V DC at 1.5A, which is the rating the GNPC-1 supplies. So check the model number printed on your camera against that guide, then plan the run with the camera cable Google supplies to security professionals.

The adapter stays indoors at the outlet, which means the camera end needs no outdoor receptacle and no in-use cover. A basement outlet to a second-story soffit sits inside the 75 ft budget, and that's the route most pro jobs take.

Nest Cam Outdoor (wired, 2nd gen) GPJ15 - 7.5V 1.5AGoogle-supplied camera cable18 AWG, up to 75 ftIndoor outlet, Class 2

05Mechanical

Size, plug, terminals and the mounting tab

The housing is a slim two-prong unit at 1.71 x 1.15 x 3.75 in., with a mounting tab molded into the top. A screw through that tab anchors the adapter flat to the wall plate, so camera power can't be defeated by pulling a brick out of a socket. That's the detail commercial and multi-tenant sites ask for.

Element What it is What it means on the job
Housing 1.71 x 1.15 x 3.75 in., indoor Class 2 unit Fits a standard duplex receptacle and leaves the second outlet usable
Plug Two-prong plug-in (NEMA 1-15P) Any US indoor outlet, and it's double insulated so there's no ground pin
Terminals Two screw terminals marked + and - on the bottom edge The Google-supplied camera cable lands here; match polarity and tighten fully
Mounting tab Security mounting screw hole molded into the top One screw into the wall plate and the adapter stays put

06Install

Put the GNPC-1 in, in three steps

  1. Plan the run

    Pick an interior outlet and confirm the route to the camera is 75 ft or less on 18 AWG or heavier. Heavier wire buys you margin, so size up if the route is near the limit.

  2. Land the camera cable

    Put the conductors of the Google-supplied camera cable under the two screw heads on the bottom of the adapter. Match the + and - markings and tighten them fully, then run and dress the cable to the camera and connect the camera end per Google's guide for that model.

  3. Anchor it and power up

    Drive a screw through the mounting tab into the wall plate, plug the adapter in, and confirm the camera comes up. The adapter stays indoors at the outlet, in a dry location.

For an outdoor camera, Google's install guide describes two routes: out to an outdoor outlet, or in through a vent or a drilled hole to an indoor one. The indoor route is the one the GNPC-1 is built for, and the 75 ft budget is what makes that reach practical.

07Ordering

Part number and what goes with it

Order it as GNPC-1, the Versa Wireless Google Nest Cam power adapter. It's the one accessory on this site that isn't a sensor part. It ships as the adapter alone, because Google supplies the camera cable to security professionals with the camera hardware. You'll find it through the SS&Si Dealer Network on your dealer account, direct on the GNPC-1 product page, and our Where to Buy page lists every Versa distributor.

Related on the same job: Versa accessories holds the brown and black cover packs for the MINI and SHOCK-319 sensors. The wireless intrusion sensors cover the 319.5, 345 and 433 MHz panels. If you install professionally and don't have a wholesale account with Versa yet, contact Versa Wireless and we'll get you set up.

08FAQ

GNPC-1 datasheet questions

What is the GNPC-1 output voltage and current?

The GNPC-1 is a Class 2 Power Unit with a 100-240V AC input at 50/60 Hz and 0.5A, and a 7.5V DC, 1.5A output. So you can plug it into any outlet you'd find on a US job. It uses a two-prong NEMA 1-15P plug and measures 1.71 x 1.15 x 3.75 in. It's Class II double insulated, and it's an Efficiency Level VI external power supply.

What Google Nest cameras does the GNPC-1 power?

The GNPC-1 supplies 7.5V DC at 1.5A. That's the adapter rating Google's Safety and Regulatory Guide lists for the GPJ15 variant of the Nest Cam Outdoor (wired, 2nd gen). Google lists the rating per camera variant, so the model number printed on the camera is what tells you which adapter it takes. Check that number against Google's guide before you order, then plan the run with the camera cable Google supplies to security pros.

How far can the GNPC-1 run cable?

Up to 75 ft (22.9 m) of 18 AWG or heavier Class 2 conductor is the run budget we rate it for. That's enough to put the adapter at an interior outlet and still reach a camera on the far side of the house. Treat 75 ft as the ceiling of the run budget rather than a target. Heavier wire buys you margin, and thinner wire spends it faster than the length alone suggests.

Does the GNPC-1 come with a camera cable?

No cable is bundled, and that's deliberate. Google supplies the matching camera cable to security professionals with the camera hardware, so a kit with a second one is a part you'd pay for twice. The GNPC-1 is the transformer alone, and it ends in two screw terminals marked + and - where that cable lands.

Is the GNPC-1 safety certified?

Yes. The GNPC-1 is ETL Listed by Intertek under control number 5030071 80CD, and the label prints that it conforms to UL STD. 1310 and is certified to CSA STD. C22.2 No. 223. Those are the Class 2 power unit standards for an indoor adapter like this one. Short-circuit protection and NTC thermal protection are both built in, so a fault at the output shuts it down and it recovers on its own once the fault clears.

Can the GNPC-1 be locked down to prevent tampering?

Yes. A mounting tab is molded into the top of the housing with a screw hole through it. Drive a screw through the tab into the wall plate and the adapter sits flat and stays put. So camera power can't be defeated by pulling a brick out of a socket.

Can the GNPC-1 be used for outdoor Nest Cam installs?

Yes, and that's how we'd do it. The GNPC-1 is an indoor Class 2 unit, so it sits at an interior receptacle and you run the cable out to the camera. That means the camera end needs no outdoor outlet and no in-use cover. Google's install guide describes both the outdoor-outlet route and the indoor route, and the 75 ft budget is what makes the indoor route practical.

Where can I find the GNPC-1 datasheet and spec sheet?

Right here, and as a printable PDF from the download button at the top of this page. It lists the electrical input and output, the dimensions, the wire gauge and run budget, the protection features and the ETL listing to UL 1310 and CSA C22.2 No. 223. The installer guide covers the cable routes, and the product page has the photos.

Need it on the truck? The file is the same document, with the figures.

Download the datasheet (PDF)Technical datasheet - DS_GNCP-1_05-2026 - 3 pages - 369 KB

Regulatory

ETL Listed: Conforms to UL 1310 and CSA C22.2 No. 223 standards for Class II indoor-use transformers

The adapter's label also prints Class 2 Power Unit, Class II, Efficiency Level VI, Indoor Use Only, "Risk of electric shock. Dry locations use only", the ETL control number 5030071 80CD and Made in Vietnam. You can check the listing through Intertek's ETL mark page, and the US Department of Energy explains the Level VI efficiency mark.

Specifications and product details are subject to change without notice.

Versa Wireless is not responsible for typographical errors or outdated information

Cart 0

Your cart is currently empty.

Start Shopping