Sensor covers and camera power
Accessories
Brown and black cover 10-packs for the MINI contacts and the SHOCK-319, plus the GNPC-1 power adapter for wired Google Nest Cam installs.
Accessory - Camera power adapter
GNPC-1 Google Nest Cam Power Adapter
Google Nest Cam power adapter that pairs with the Google-supplied camera cable, ETL listed 7.5V DC 1.5A with a 75 ft run rating on 18 AWG.
Accessory - Replacement sensor covers
MINI Black Covers 10-Pack
Black sensor cover 10-pack for the MINI-319, 345 and 433: ten sensor covers, ten magnet covers and ten bases.
Accessory - Replacement sensor covers
MINI Brown Covers 10-Pack
Brown sensor cover 10-pack for the MINI-319, 345 and 433: ten sensor covers, ten magnet covers and ten bases.
Accessory - Replacement sensor covers
SHOCK-319 Black Covers 10-Pack
Black sensor cover 10-pack for the SHOCK-319: ten sensor covers, ten magnet covers and ten magnet bases.
Accessory - Replacement sensor covers
SHOCK-319 Brown Covers 10-Pack
Brown sensor cover 10-pack for the SHOCK-319: ten sensor covers, ten magnet covers and ten magnet bases.
Overview
Color covers for the sensors, and power for a wired Nest Cam
Versa Wireless accessories are two things. Four cover packs change the color of a sensor that's already on the frame. One power adapter feeds a wired Google Nest Cam from an indoor outlet. The MINI brown and MINI black packs fit the MINI-319, MINI-345 and MINI-433, because the three contacts share one housing. The SHOCK-319 brown and SHOCK-319 black packs fit the larger shock sensor housing. And the GNPC-1 is a 7.5V DC, 1.5A Class 2 adapter for wired Google Nest Cam installs.
Every cover pack is the same 30 pieces: ten sensor covers, ten magnet covers and ten magnet bases, all in one color. So you get a full color change for ten sensors with the magnets matched too. The sensor ships white, and most homes mix white trim, wood frames and dark window profiles on the same job. Carrying one pack of brown and one of black means you fit the frame you find, without stocking a separate sensor for every color.
Here's what makes the swap worth doing on a live system. The cover slides forward off the base and lifts away by hand, so nothing gets pried and nothing gets unscrewed. The base stays taped to the frame and the board stays in it. That means your alignment and the zone at the panel are untouched. One thing to plan for, though: sliding the cover off is a monitored event. The sensor sends a tamper signal. So you disarm the system or put the panel in test mode first, do the swap, and run the panel's test before you leave.
The GNPC-1 is the one accessory here that isn't a sensor part. It's transformer-only, so instead of a captive cord it ends in two screw terminals marked + and -. The camera cable Google supplies to security professionals lands right there. It's rated for a run of up to 75 ft on 18 AWG or heavier. So you can plan a basement outlet to a second-story soffit on paper. We built it that way so one power SKU covers the wired Nest Cam jobs.
Pick by sensor
Start with the sensor or the camera on the job
Three cards. Find the part that's already on the wall, and the accessory is the one on the card.
The MINI door and window contacts
One MINI pack fits all three contacts, because the MINI-319, MINI-345 and MINI-433 share the 2.2 x 1 x 0.25 in. housing. Only the radio inside differs. So a van that covers several panel types still carries one box of brown and one of black. After the swap the blue and green LEDs run for 15 minutes, so you can check the magnet before you walk away.
The SHOCK-319 shock sensor and contact
The SHOCK-319 uses the larger 2.85 x 1.15 x 0.75 in. housing, so it has its own pack rather than sharing the MINI one. The cover slides off the same way, and the base and the board stay on the frame. That means the zone stays enrolled and the sensitivity setting stays where you put it. The blue LED runs for 5 minutes after the cover comes off.
A wired Nest Cam on an indoor outlet
The GNPC-1 supplies 7.5V DC at 1.5A, which is the adapter rating Google lists for the GPJ15 variant of the Nest Cam Outdoor (wired, 2nd gen). Check the model number printed on the camera against Google's guide. Then plan one run of up to 75 ft on 18 AWG, with the camera cable Google supplies. The adapter stays indoors at the outlet, so the camera end needs no outdoor receptacle.
Which MINI is which? The frequency and the panels each contact suits live on the sensor pages. The panel compatibility guide lists every Versa sensor by panel family. Our article on changing a Versa sensor cover shows the swap step by step, with photos.
Compare
The four cover packs side by side, and the GNPC-1 at a glance
Same 30 pieces, same slide-on fit and the same tamper on removal. The differences are the sensor each pack fits and the color.
| Cover pack | MINI brown | MINI black | SHOCK-319 brown | SHOCK-319 black |
|---|---|---|---|---|
| Fits | MINI-319, MINI-345, MINI-433 | MINI-319, MINI-345, MINI-433 | SHOCK-319 | SHOCK-319 |
| Color | Brown, matte molded plastic | Black, matte molded plastic | Brown, matte molded plastic | Black, matte molded plastic |
| Pack | 30 pieces: 10 sensor covers, 10 magnet covers, 10 magnet bases | 30 pieces: 10 sensor covers, 10 magnet covers, 10 magnet bases | 30 pieces: 10 sensor covers, 10 magnet covers, 10 magnet bases | 30 pieces: 10 sensor covers, 10 magnet covers, 10 magnet bases |
| Transmitter body it fits | 2.2 x 1 x 0.25 in. | 2.2 x 1 x 0.25 in. | 2.85 x 1.15 x 0.75 in. | 2.85 x 1.15 x 0.75 in. |
| Magnet gap after refit | 1 in. on wood, 1/4 in. on metal | 1 in. on wood, 1/4 in. on metal | 1 in. on wood, 1/4 in. on metal | 1 in. on wood, 1/4 in. on metal |
| LEDs after the cover comes off | Blue and green for 15 minutes | Blue and green for 15 minutes | Blue for 5 minutes | Blue for 5 minutes |
| Battery behind the cover | CR2032, plus side up | CR2032, plus side up | Versa CR2U (Panasonic CR2), plus end up | Versa CR2U (Panasonic CR2), plus end up |
| Tamper | Removing the cover sends a tamper signal; disarm or enter test mode first | Removing the cover sends a tamper signal; disarm or enter test mode first | Removing the cover sends a tamper signal; disarm or enter test mode first | Removing the cover sends a tamper signal; disarm or enter test mode first |
| Tools | None for the cover change | None for the cover change | None for the cover change | None for the cover change |
| Versa part number | V0000659 | V0000661 | V0000658 | V0000660 |
| Adapter | GNPC-1 |
|---|---|
| Output | 7.5V DC, 1.5A, the rating Google lists for the GPJ15 variant of the Nest Cam Outdoor (wired, 2nd gen) |
| Input | 100-240V AC, 50/60 Hz, 0.5A, two-prong plug |
| Run budget | Up to 75 ft (22.9 m) on 18 AWG or heavier conductor |
| Terminals | Two screw terminals marked + and -, no captive cord; the Google-supplied camera cable lands here |
| Mounting | Security screw tab that anchors the adapter flat to the wall plate |
| Protection | Short-circuit shutdown with self-recovery; NTC inrush and overheat protection |
| Size and use | 1.71 x 1.15 x 3.75 in.; indoor, dry locations only |
| Listings | ETL Listed by Intertek, control number 5030071 80CD; UL 1310 and CSA C22.2 No. 223; Class 2 Power Unit, Class II, Efficiency Level VI |
| Datasheet | GNPC-1 datasheet |
The cover packs are cosmetic housing parts for indoor, dry locations. They don't change what the sensor does or which panel it suits. After any cover change, re-test the sensor at the panel and confirm the zone restores with the door or window closed.
Setup
Change a sensor cover without re-enrolling
Disarm first
Disarm the system or put the panel in test mode, because taking the cover off sends a tamper. On a MINI or a SHOCK-319 the panel sees that as a monitored event, which is exactly what you want when the system is armed.
Slide the old cover off
Push the sensor cover forward and lift it away. The base stays taped to the frame and the board stays in it, so the sensor stays enrolled and your alignment never moves. There's no screw to back out and nothing to pry.
Slide the new cover on
Line the new cover up with the base and slide it on until it seats. The install LEDs wake up when the cover comes off. That's 15 minutes on a MINI and 5 minutes on the SHOCK-319, so you can check the magnet with the opening closed.
Do the magnet, then test
Lift the old magnet cover off, then fit the new magnet cover and base on the moving part of the opening. Keep the gap inside the sensor's limit, which is 1 in. on wood and 1/4 in. on metal. Then run the panel's test and confirm the zone restores.
If you're swapping the battery at the same time, it's the same opening. Fit a CR2032 plus side up on a MINI, or a Versa CR2U plus end up on the SHOCK-319, before the cover goes back on. The GNPC-1 has its own three-step install, so it's covered below.
Nest Cam power
Install the GNPC-1 in three steps
Plan the run first, so the route from an interior outlet to the camera is 75 ft or less on 18 AWG or heavier. Then land the conductors of the Google-supplied camera cable under the two screw heads, matching the + and - markings. Run the cable to the camera. Finally, drive a screw through the mounting tab into the wall plate, plug the adapter in, and confirm the camera comes up.
Where to buy
Order through your distributor, or direct from Versa
Don't see your distributor? See all Versa distributors -> or open a Versa dealer account.
At a glance
FAQ
Accessory questions installers ask
What accessories does Versa Wireless sell?
Replacement cover packs for the MINI and SHOCK-319 sensors in brown and black, and the GNPC-1 power adapter for wired Google Nest Cam installs. Each cover pack holds 30 pieces: ten sensor covers, ten magnet covers and ten magnet bases, all in one color. The GNPC-1 is a transformer-only 7.5V DC, 1.5A Class 2 adapter, and the camera cable Google supplies lands on its two screw terminals.
What comes in a Versa cover 10-pack?
Thirty pieces. Ten sensor covers, ten magnet covers and ten magnet bases, all in one color. That's a complete housing change for ten sensors and their magnets, so the pair matches the frame instead of just the sensor. The sensor itself ships white, and the packs are how you change it.
Do the cover colors fit all Versa sensors?
The MINI packs fit the MINI-319, MINI-345 and MINI-433, which share one housing, so one cover fits all three. The SHOCK-319 packs fit the SHOCK-319, which uses the larger shock sensor housing. Both families come in brown and black 10-packs, and white is the color the sensor ships in.
That's what makes it worth stocking by color instead of by model. A van covering several panel types still carries one box of brown and one of black, not one box per sensor.
Do I need tools to change a Versa sensor cover?
No. Versa MINI and SHOCK-319 covers slide off and on by hand, so there's no screw to back out and nothing to pry. The base stays mounted on the frame and the board stays in the base, which means the sensor stays enrolled at the panel. The same opening is how you reach the battery.
Will taking the cover off set off a tamper?
Yes, if the system is armed. Removing the cover is a monitored event on every Versa MINI and SHOCK-319, and the panel sees it as a tamper. That's exactly what you want on a live system.
So disarm the system or put the panel in test or programming mode before you slide the cover off. Do the swap, then clear the test when you're done. The same goes for a battery change, because it's the same opening.
Can I paint a Versa sensor cover?
Yes, and that's one reason the cover is a separate part. It comes off without removing the board, so a cover can go to the paint booth on its own and slide back on afterwards. Mask the indicator window and the label before you spray, and leave the base on the frame. If you need a color that paint can't give you cleanly, brown and black are the two we stock as 10-packs.
Which Nest Cam does the GNPC-1 power, and how long can the run be?
The GNPC-1 supplies 7.5V DC at 1.5A. That's the adapter rating Google's Safety and Regulatory Guide lists for the GPJ15 variant of the Nest Cam Outdoor (wired, 2nd gen). Google lists the rating per camera variant, so the model number printed on the camera is what tells you which adapter it takes. Check it against Google's guide before you order.
Use 18 AWG or heavier Class 2 conductor, and the GNPC-1 is rated for up to 75 ft (22.9 m) at that gauge. Treat 75 ft as the ceiling of the run budget rather than a target. Heavier wire buys you margin, and thinner wire spends it faster. The adapter stays indoors at the outlet, so the camera end needs no outdoor receptacle and no in-use cover.
Where do dealers buy Versa accessories?
Through Versa's distributors. The cover packs are at the SS&Si Dealer Network and WAVE Electronics on your dealer account, and the GNPC-1 is at SS&Si. You can also order everything on this page direct from this site. The Where to Buy page lists every Versa distributor, and installers can open a Versa wholesale account for dealer pricing.
Resources
Datasheet, manuals and reading
Every installation manual, datasheet and firmware page lives in the library, and each product page links to its own manual. The sensor manuals carry the battery type and the handling warning for each sensor the covers fit. The sensors themselves are in door and window sensors and shock sensors.
Insights





